Message Boards
Today's Active Topics Today's Active Cases Browse Forum Categories My Recent Activity My Messages Private Groups My Marked Threads My Subscriptions
Today's Active Images Today's Active Polls Most Active Topics Global Townie Map Advanced Message Board Search Message Board Terms of Use

The Advantages of Owning an In-Office Ceramic Oven by Marshall Hanson, DDS

View Comments (0) More by this author (1)

Becoming efficient at predictably achieving successful clinical outcomes is the goal that most of us as clinicians are continually striving for.

Working efficiently allows us to be profitable while at the same time offer the benefit to our patients of completing their required treatment in shorter or fewer appointments. Predictability, when it comes to achieving a desired clinical result, boosts our confidence in caring for our patients, minimizes stress and strengthens a good reputation.

There are many dental products and equipment available today designed with the intent to appeal to our desire for efficiency, profitability and predictability. In this article, I wish to highlight just one – and share with you the advantages that we have found in our practice of owning an in-office ceramic oven.

“But Dr. Hanson,” you might say, “What use would I have for an in-office oven if I do not make my own crowns?” Even if you send your crowns out to be made by an off-site dental laboratory, the advantages of a ceramic oven in your office are still applicable, and will potentially increase your efficiency and elevate your ability to predictably achieve outcomes that you and your patients will be pleased with in at least the following two ways:

1. Customization – “the ability to blend” – chairside!

Many of us can sympathize with trying in the crown at the delivery appointment and silently asking ourselves, “Do I really want to seat this crown, or shall I send it back to the lab and see if they can alter the color or value slightly to help it blend in just a little bit better?” Just the fact that we are asking the question is enough to confirm that sending it back is the right thing to do, but suddenly then, we are forced to face the following truthserum flood of thoughts:

“If I send this back, then we will have to make a new appointment... and get her numb again... and she’s not going to be thrilled with wearing a temporary for another two weeks... speaking of that, I am going to have to make her a new temporary now since we cut the last one off to try in the crown. How am I going to explain to her that our work didn’t turn out right? Do I blame it on the lab? Did I forget to send photos? Is she going to think that I don’t know what I am doing...?”



This silent thought-contained conversation has the potential to build on itself and quickly become mentally and internally straining! However, if there is a ceramic oven down the hall, along with some custom stains and glaze, this story may have a chance for a different ending.

You explain to your patient that you happen to have the technology in your office to customize her crown and make it “blend-in” even better! Thirty minutes later, satisfied with the aesthetics, you are seating her new crown. You both feel great about the results. She is pleased with your artistic ability and now thinks, “You are a magician” for blending her new tooth in so nicely with the rest of her smile. She says she will be referring her friends “for sure!”

Click here to watch the video:
“How to Add a Contact to an Existing Restoration.”

Now, maybe that sounds simplified, or a bit over-the-top to you, but you get the picture; you were efficient, there was no additional appointment, you achieved predictable aesthetic results the first time around, and finished with a pleased customer and a heightened sense of self-confidence – a much better ending to the story!

Proceed as follows to apply individualized characterizations and glaze:
  1. Thoroughly clean and dry the restoration after clinical try-in.
  2. Extrude Glaze Paste from the syringe and mix.
  3. Apply the glazing paste evenly to the entire restoration using a small brush.
  4. If characterizations are desired, the restoration can be individualized using shades and stains before firing.
  5. Extrude Shades and Stains from the syringe and mix thoroughly.
  6. The ready-to-use Shades and Stains may be slightly thinned using Glaze Liquid. However, the consistency should still remain pasty.
  7. Apply mixed Shades and Stains directly into the unfired glaze layer using a fine brush.
  8. Conduct the corrective firing if characterization is applied to an already crystallized restoration.

2. Ideal Contacts – “what was once left open can now be made closed” – chairside!

Similar to the first example, the solution, when finding that the crown that we hope to deliver today has insufficient proximal contact, might require a long list of additional steps, lost time, and disappointment to both us and our patient. However, if there is a ceramic oven down the hall, along with some porcelain powder and liquid add-on, suddenly we have an alternative avenue available for ensuring predictable contacts every time at the delivery appointment.

Processing:
  1. Mix IPS e.max CAD Crystall/Add-On with IPS e.max CAD Crystall/Add-On Liquid to an easy-to-contour consistency. Ensure even mixing of the add-on material and the liquid in order to achieve an optimum firing result.
  2. Apply the mixed add-on material directly in the areas to be adjusted and fire.
  3. Conduct the corrective firing if Add-On is applied on an already crystallized restoration.

The advantages of using an in-office ceramic oven create opportunities in our office for increased efficiency and predictability that may not exist for us otherwise. Carefully selecting and utilizing the advanced materials and technologies that we have available today will assist us in attaining our goal as clinicians. There is an elevated feeling of confidence and satisfaction that can be discerned the closer we get to blending efficiency with predictability in achieving successful clinical outcomes for the patients in our practices (this article highlights only one of the products or equipment that can help us get there). And along our individual yet collective journey of “getting there,” we will come to find and conclude that the feeling that comes with achieving such a goal is well worth striving for!

  Author's Bio
Dr. Marshall Hanson is an Accredited Member of the American Academy of Cosmetic Dentistry. He graduated with honors from the University of the Pacific Aurthur A. Dugoni School of Dentistry (UOP) in 2007, and has owned a private practice in Chandler, Arizona, since 2008. Dr. Hanson loves spending time with his wife and four children, competing in triathlons and other outdoor sports. Ever seeking further learning and progress, he continually works to improve his clinical and artistic skills as a dentist, completing much of his own dental labwork for his patients.

Dentaltown Magazine
September 2025
Dentaltown Magazine September 2025 Read Current Issue Read Archived Issues
Sponsors
Townie Perks
Townie® Poll
Who or what do you turn to for most financial advice regarding your practice?
  
Site Menu
Message Boards Magazine Continuing Education Podcasts Blogs Classifieds Dental News Events Townie® Poll Ebooks Townie Choice Awards
Company Info
Contact Us Advertise With Us Howard Farran DDS, MBA Policies and Agreements
Site Help
Sally Gross, Member Services Specialist
Phone: +1-480-445-9710
Email: sally@farranmedia.com
©2025 Dentaltown, a division of Farran Media • All Rights Reserved
9633 S. 48th Street Suite 200 • Phoenix, AZ 85044 • Phone:+1-480-598-0001 • Fax:+1-480-598-3450